Information On reinforced concrete

Image:Sainte Jeanne d'Arc-1-large.jpg (Nice France : architect Jacques Dror, 1926–1933]] Reinforced concrete is concrete in which reinforcement bars ("rebar "), reinforcement grids, Steel Plate Construction or fiber reinforced concrete have been incorporated to strengthen the concrete in tension (physics) The term Ferro Concrete refers only to concrete that is reinforced with iron or steel. Other materials used to reinforce concrete can be organic and inorganic fibres as well as composite materials in different forms. Concrete is strong in physical compression but weak in tension, thus adding reinforcement increases the strength in tension. In addition, the failure strain of concrete in tension is so low that the reinforcement has to hold the cracked sections together. For a strong, ductile and durable construction the reinforcement shall have the following properties: * High strength * High tensile strain * Good bond to the concrete * Thermal compatibility * Durability in the concrete environment In most cases reinforced concrete uses steel rebars that have been inserted to add strength.

Use in construction

Image:SagradaFamiliaRoof2.jpg s roof in construction (2009)]] Concrete is reinforced to give it extra tensile strength; without reinforcement, many concrete buildings would not have been possible. Reinforced concrete can encompass many types of structures and components, including slab , wall , beam (structure) column , foundation (architecture) framing (construction) and more. Reinforced concrete can be classified as precast or cast in-situ concrete Much of the focus on reinforcing concrete is placed on floor systems. Designing and implementing the most efficient floor system is key to creating optimal building structures. Small changes in the design of a floor system can have significant impact on material costs, construction schedule, ultimate strength, operating costs, occupancy levels and end use of a building.

Behavior of reinforced concrete

Materials

Concrete is a mixture of cement (usually Portland cement and stone construction aggregate When mixed with a small amount of water, the cement hydrates form microscopic opaque crystal lattices encapsulating and locking the aggregate into a rigid structure. Typical concrete mixes have high resistance to physical compression stress (physics) s (about ; however, any appreciable tension (mechanics) (e.g. due to bending will break the microscopic rigid lattice resulting in cracking and separation of the concrete. For this reason, typical non-reinforced concrete must be well supported to prevent the development of tension. If a material with high strength in tension, such as steel is placed in concrete, then the composite material, reinforced concrete resists compression but also bending, and other direct tensile actions. A reinforced concrete section where the concrete resists the compression and steel resists the tension can be made into almost any shape and size for the construction industry.

Key characteristics

Three physical characteristics give reinforced concrete its special properties. First, the coefficient of thermal expansion of concrete is similar to that of steel, eliminating large internal stresses due to differences in heat expansion or contraction. Second, when the cement paste within the concrete hardens this conforms to the surface details of the steel, permitting any stress to be transmitted efficiently between the different materials. Usually steel bars are roughened or corrugated to further improve the chemical bond or cohesion between the concrete and steel. Third, the pH chemical environment provided by the alkali reserve (KOH, NaOH) and the portlandite (calcium hydroxide contained in the hardened cement paste causes a passivation film to form on the surface of the steel, making it much more resistant to corrosion than it would be in neutral or acidic conditions. When the cement paste exposed to the air and meteoric water reacts with the atmospheric CO₂, portlandite and the Calcium Silicate Hydrate (CSH of the hardened cement paste become progressively carbonated and the high pH gradually decreases from 13.5 – 12.5 to 8.5, the pH of water in equilibrium with calcite (calcium carbonate and the steel is no longer passivated. As a rule of thumb, only to give an idea on orders of magnitude, steel is protected at pH above ~11 but starts to corrode below ~10 depending on steel characteristics and local physico-chemical conditions when concrete becomes carbonated. Carbonation of concrete along with chloride ingress are amongst the chief reasons for the failure of reinforcement bar in concrete. The relative cross-sectional area of steel required for typical reinforced concrete is usually quite small and varies from 1% for most beams and slabs to 6% for some columns. rebar are normally round in cross-section and vary in diameter. Reinforced concrete structures sometimes have provisions such as ventilated hollow cores to control their moisture & humidity. Distribution of concrete (in spite of reinforcement) strength characteristics along the cross-section of vertical reinforced concrete elements is inhomogeneous http://www.concreteresearch.org/PDFsandsoon/Inhomog%20Denver.pdf article "Concrete Inhomogeneity of Vertical Cast-In-Situ Elements In Frame-Type Buildings"].

Anti-corrosion measures

In wet and cold climates, reinforced concrete for roads, bridges, parking structures and other structures that may be exposed to deicing salt may benefit from use of epoxy-coated, hot dip galvanised or stainless steel rebar, although good design and a well-chosen cement mix may provide sufficient protection for many applications. Epoxy coated rebar can easily be identified by the light green colour of its epoxy coating. Hot dip galvanized rebar may be bright or dull grey depending on length of exposure, and stainless rebar exhibits a typical white metallic sheen that is readily distinguishable from carbon steel reinforcing bar. Reference ASTM standard specifications A767 Standard Specification for Hot Dip Galvanised Reinforcing Bars, A775 Standard Specification for Epoxy Coated Steel Reinforcing Bars and A955 Standard Specification for Deformed and Plain Stainless Bars for Concrete Reinforcment Another, cheaper way or protecting rebars is coating them with zinc phosphate "Effect of zinc phosphate chemical conversion coating on corrosion behaviour of mild steel in alkaline medium: protection of rebars in reinforced concrete" Sci. Technol. Adv. Mater. 9 (2008) 045009 (http://www.iop.org/EJ/abstract/1468-6996/9/4/045009 free download]) Zinc phosphate slowly reacts with calcium cations and the hydroxyl anions present in the cement pore water and forms a stable hydroxyapatite layer. Penetrating sealants typically must be applied some time after curing. Sealants include paint, plastic foams, films and aluminum foil felts or fabric mats sealed with tar, and layers of bentonite clay, sometimes used to seal roadbeds. Corrosion inhibitor such as calcium nitrite Ca(NO₂)₂] can also be added to the water mix before pouring concrete. Generally, 1–2 wt. % of Ca(NO₂)₂] with respect to cement weight is needed to prevent the corrosion of the rebars. The nitrite anions is a mildy oxidizer that oxidizes the soluble and mobile ferrous ion (Fe²⁺) present at the surface of the corroding steel and causes it to precipitate as an insoluble ferric hydroxide (Fe(OH)₃). This causes the passivation of steel at the anodic oxidation sites. Nitrite is a much more active corrosion inhibitor than nitrate a less powerful oxidizer of the divalent iron.

Reinforcement and terminology

A beam bends under bending moment resulting in a small curvature. At the outer face (tensile face of the curvature the concrete experiences tensile stress while at the inner face (compressive face it experiences compressive stress. A "singly-reinforced" concrete means that the concrete element is only reinforced near the tensile face and the reinforcement, called tension steel, is designed to resist the tension. A "doubly-reinforced" concrete means that beside the tensile reinforcement the concrete element is also reinforced near the compressive face for assisting the concrete to resist compression. The latter reinforcement is called compression steel. An "under-reinforced" concrete means that the tension capacity of the tensile reinforcement is smaller than the combined compression capacity of the concrete and the compression steel (under-reinforced at tensile face). When the reinforced concrete element is subject to increasing bending moment, the tension steel yields while the concrete does not reach its ultimate failure condition. As the tension steel yields and stretches, an "under-reinforced" concrete also yields in a ductile manner, exhibiting a large deformation and warning before its ultimate failure. An "over-reinforced" concrete means that the tension capacity of the tension steel is greater than the combined compression capacity of the concrete and the compression steel (over-reinforced at tensile face). An "over-reinforced" element will fail suddenly, when the concrete fails brittle and crashes before yielding of the tension steel. It is however possible to push the design of an "over-reinforced" concrete element to "under-reinforced" concrete element by adding sufficient compression steel. There is however a limit in the quantity of both tension and compression steel for practically placement of reinforcement.-Balaji. Steel reinforced concrete elements should normally be designed to be under-reinforced so users of the structure will receive warning of impending collapse. Characteristic strength strength of a material where less than 5% of the specimen show lower strength. Design strength strength of a material including a material safety factor. Ultimate limit state theoretical failure point with a certain probability. State under factored loads and factored resistances. Nominal strength actual strength from the material properties is called the nominal strength.http://www.aboutcivil.com/reinforced-cement-concrete-design.html | SJ Soft Technologies Its relation with design strength can be represented as:

Nominal x Ø  Design strength

Prestressed Concrete

Prestressed concrete is a technique that greatly increases loadbearing strengh of concrete beams. The reinforcing steel in the bottom part of the beam, which will be subjected to tensile forces when in service, is placed in tension prior to the concrete being poured around it. Once the concrete has hardened, the tension on the reinforcing steel is released, placing a built in compressive force on the concrete. When loads are applied, the reinforcing steel takes on more stress and the compressive force in the concrete is reduced, but does not become a tensile force. Since the concrete is always under compression, it is less subject to cracking and failure.http://www.ferrericon.com/Whatis.html

Common failure modes of steel reinforced concrete

Reinforced concrete can fail due to inadequate strength, leading to mechanical failure, or due to a reduction in its durability. Corrosion and freeze/thaw cycles may damage poorly designed or constructed reinforced concrete. When rebar corrodes, the oxidation products (rust expand and tends to flake, cracking the concrete and unbonding the rebar from the concrete. Typical mechanisms leading to durability problems are discussed below.

Mechanical failure

Reinforced concrete can be considered to have failed when significant cracks occur. Cracking of the concrete section can not be prevented; however, the size of and location of the cracks can be limited and controlled by reinforcement, placement of control joints, the curing methodology and the mix design of the concrete. Cracking defects can allow moisture to penetrate and corrode the reinforcement. This is a limit state design#Serviceability Limit State failure in limit state design Cracking is normally the result of an inadequate quantity of rebar, or rebar spaced at too great a distance. The concrete then cracks either under excess loading, or due to internal effects such as early thermal shrinkage when it cures. Ultimate failure leading to collapse can be caused by crushing of the concrete matrix, when stresses exceed its strength; by yield (engineering) of the rebar; or by bond failure between the concrete and the rebar.

Carbonation

Image:RebarCloseup.jpg Carbonation, or neutralisation, is a chemical reaction between carbon dioxide in the air with calcium hydroxide and hydrated calcium silicate in the concrete. The water in the pores of Portland cement concrete is normally alkaline with a pH in the range of 12.5 to 13.5. This highly alkaline environment is one in which the embedded steel is passivated and is protected from corrosion. According to the Pourbaix diagram for iron, the metal is passive when the pH is above 9.5.lt;/ref> The carbon dioxide in the air reacts with the alkali in the cement and makes the pore water more acidic, thus lowering the pH. Carbon dioxide will start to carbonate the cement in the concrete from the moment the object is made. This [[carbonation]] process will start at the surface, then slowly move deeper and deeper into the concrete. The rate of carbonation is dependent on the relative humidity of the concrete - a 50% relative humidity being optimal. If the object is cracked, the carbon dioxide in the air will be better able to penetrate into the concrete. When designing a concrete structure, it is normal to state the concrete cover for the rebar (the depth within the object that the rebar will be). The minimum concrete cover is normally regulated by design or building code . If the reinforcement is too close to the surface, early failure due to corrosion may occur. The concrete cover depth can be measured with a Cover Meter However, carbonated concrete only becomes a durability problem when there is also sufficient moisture and oxygen to cause electro-potential corrosion of the reinforcing steel. One method of testing a structure for carbonation is to drill a fresh hole in the surface and then treat the cut surface with phenolphthalein indicator solution. This solution will turn pink] when in contact with alkaline concrete, making it possible to see the depth of carbonation. An existing hole is no good because the exposed surface will already be carbonated.

Chlorides

Image:October 2006 021.jpg Hainesburg, New Jersey, is 115 feet (35 m) tall and 1,100 feet (335 m) long, and was heralded as the largest reinforced concrete structure in the world when it was completed in 1910 as part of the Lackawanna Cut-Off rail line project. The Lackawanna Railroad was a pioneer in the use of reinforced concrete.]] Chloride , including sodium chloride can promote the corrosion of embedded steel rebar if present in sufficienty high concentration. Chloride anions induce both localized corrosion (pitting corrosion and generalized corrosion of steel reinforcements. For this reason, only use fresh raw water or potable water for mixing concrete. Insure that the coarse and fine aggregates do not contain chlorides. Do not use admixtures that contain chlorides. It was once common for calcium chloride to be used as an admixture to promote rapid set-up of the concrete. It was also mistakenly believed that it would prevent freezing. However, this practice has fallen into disfavor once the deleterious effects of chlorides became known. It should be avoided when ever possible. The use of de-icing salts on roadways, used to reduce the freezing point of water, is probably one of the primary causes of premature failure of reinforced or prestressed concrete bridge decks, roadways, and parking garages. The use of epoxy reinforcing bars and the application of cathodic protection has mitigated this problem to some extent. Properly designed concrete mixtures that have been allowed to cure properly are effectively impervious to the effects of de-icers. (One common problem today is that concrete is allowed to "dry" (dries out) in two to three days by contractors before it cures and thus ultimately develops less than 10% of its design strength). Another important source of chloride ions is from sea water Sea water contains by weight approximately 3.5 wt.% salts These salts include sodium chloride magnesium sulphate calcium sulphate and bicarbonate . In water these salts dissociate in free ions (Na⁺, Mg²⁺, Cl^-, SO₄^2-, HCO₃^-) and migrate with the water into the capillary of the concrete. Chloride ions are particularly aggressive for the corrosion of the carbon steel reinforcement bars and make up about 50% of these ions.

Alkali silica reaction

This a reaction of amorphous silica (chalcedony chert siliceous limestone sometimes present in the aggregate with the hydroxyl ions (OH^-) from the cement pore solution. Poorly crystallized silica (SiO₂) dissolves and dissociates at high pH (12.5 - 13.5) in alkaline water. The soluble dissociated silicic acid reacts in the porewater with the calcium hydroxide (portlandite present in the cement paste to form an expansive calcium silicate hydrate (CSH . The [[Alkali Silica Reaction|alkali silica reaction]] ([[ASR]]) causes localised swelling responsible of tensile stress and cracking The conditions required for alkali silica reaction are threefold: (1) aggregate containing an alkali-reactive constituent (amorphous silica), (2) sufficient availability of hydroxyl ions (OH^-), and (3) sufficient moisture, above 75 % relative humidity (RH) within the concrete.lt;/ref>http://web.archive.org/web/20061029112122/http://www.cementindustry.co.uk/main.asp?page272 ] This phenomenon is sometimes popularly referred to as "concrete cancer . This reaction occurs independently of the presence of rebars: massive concrete structures such as dam can be affected.

Conversion of high alumina cement

Resistant to weak acids and especially sulfates, this cement cures quickly and reaches very high durability and strength. It was greatly used after World War II for making precast concrete objects. However, it can lose strength with heat or time (conversion), especially when not properly cured. With the collapse of three roofs made of prestressed concrete beams using high alumina cement, this cement was ban (law) in the United Kingdom in 1976. Subsequent inquiries into the matter showed that the beams were improperly manufactured, but the ban remained.lt;/ref>

Sulfates

Sulfates (SO₄) in the soil or in groundwater, in sufficient concentration, can react with the Portland cement in concrete causing the formation of expansive products, e.g. ettringite or thaumasite which can lead to early failure of the structure. The most typical attack of this type is on concrete slabs and foundation walls at grade where the sulfate ion, via alternate wetting and drying, can increase in concentration. As the concentration increases, the attack on the Portland cement can begin. For buried structures such as pipe, this type of attack is much rarer especially in the Eastern half of the United States. The sulfate ion concentration increases much slower in the soil mass and is especially dependent upon the initial amount of sulfates in the native soil. The chemical analysis of soil borings should be done during the design phase of any project involving concrete in contact with the native soil to check for the presence of sulfates. If the concentrations are found to be aggressive, various protective coatings can be used. Also, in the US ASTM C150 Type 5 Portland cement can be used in the mix. This type of cement is designed to be particularly resistant to a sulfate attack.

Steel plate construction

In steel plate construction, stringers join parallel steel plates. The plate assemblies are fabricated off site, and welded together on-site to form steel walls connected by stringers. The walls become the form into which concrete is poured. Steel plate construction speeds reinforced concrete construction by cutting out the time consuming on-site manual steps of tying rebar and building forms. The method has excellent strength because the steel is on the outside, where tensile forces are often greatest.

Fiber-reinforced concrete

Fiber-reinforcement is mainly used in shotcrete but can also be used in normal concrete. Fiber-reinforced normal concrete are mostly used for on-ground floors and pavements, but can be considered for a wide range of construction parts (beams, pilars, foundations etc) either alone or with hand-tied rebars. Concrete reinforced with fibers (which are usually steel, glass or Fiber-reinforced plastic is less expensive than hand-tied rebar, while still increasing the tensile strength many times. Shape, dimension and length of fiber is important. A thin and short fiber, for example short hair-shaped glass fiber, will only be effective the first hours after pouring the concrete (reduces cracking while the concrete is stiffening) but will not increase the concrete tensile strength. A normal size fibre for European shotcrete (1 mm diameter, 45 mm length—steel or "plastic") will increase the concrete tensile strength. Steel is the strongest commonly-available fiber, and come in different lengths (30 to 80 mm in Europe) and shapes (end-hooks). Steel fibres can only be used on surfaces that can tolerate or avoid corrosion and rust stains. In some cases, a steel-fiber surface is faced with other materials. Glass fiber is inexpensive and corrosion-proof, but not as ductile as steel. Recently, spun basalt fiber long available in Eastern Europe has become available in the U.S. and Western Europe. Basalt fibre is stronger and less expensive than glass, but historically, has not resisted the alkaline environment of portland cement well enough to be used as direct reinforcement. New materials use plastic binders to isolate the basalt fiber from the cement. The premium fibers are graphite reinforced plastic fibers, which are nearly as strong as steel, lighter-weight and corrosion-proof. Some experiments have had promising early results with carbon nanotubes but the material is still far too expensive for any building.

Non-steel reinforcement

Some construction cannot tolerate the use of steel. For example, MRI machines have huge magnets, and require nonmagnetic buildings. Another example are toll-booths that read radio tags, and need reinforced concrete that is transparent to radio In some instances, the lifetime of the concrete structure is more important than its initial costs. Since corrosion is the main cause of failure of reinforced concrete, a corrosion-proof reinforcement can extend a structures life substantially. For these purposes some structures have been constructed using fiber-reinforced plastic (FRP) rebar, grids or fibers. The "plastic" reinforcement can be as strong as steel. Because it resists corrosion, it does not need a protective concrete cover of 30 to 50 mm or more as steel reinforcement does. This means that FRP-reinforced structures can be lighter, have longer lifetime and for some applications be price-competitive to steel-reinforced concrete. Although FRP and concrete are brittle materials, in general structures with internal FRP reinforcement show a great elastic deformability which is comparable to the plastic deformability (ductility) of steel reinforced structures. Existing structures can be reinforced with external reinforcement as carbon fibre. In this case especially the strength can be increased. One drawback to use of FRP reinforcement is the limited fire resistance. Structures employing FRP have to ensure the strength and the anchoring of the forces at elevated temperatures. This can be achieved by defining a suitable concrete cover or protective cladding. Another problem is the effectiveness of shear reinforcement. Stirrups made by (before hardening) bended FRP show generally reduced strength through waved fibres. Exposed to strain and slip the transition between the straight and bent part is loaded by the superposition of a strong bending stress, shear and the longitudinal stress. Alternative shear reinforcement elements can solve this problem. However, the addition of short monofilament polypropylene fibers to the concrete during mixing may have the beneficial effect of reducing spall ng during a fire. In a severe fire, such as the 1996 Channel Tunnel fire conventionally reinforced concrete can suffer severe spalling leading to failure. This is in part due to the pore water remaining within the concrete boiling explosively; the steam pressure then causes the spalling. The action of fibers within the concrete is due to their ability to melt, forming pathways out through the concrete, allowing the steam pressure to dissipate.Darby, AW, http://www.tunnels.mottmac.com/files/project/3372/Airside_Road_Tunnel.pdf The Airside Road Tunnel, Heathrow Airport, England, Mott McDonald, 2003